Weighs only 32 ounces
Fully adjustable cheek rest & butt stock to fit any shooter
Wide and flat forearm for enhanced stability on a rest or pack
Vertical grip with thumbshelf
Fits any barrel contour up to 1.250" straight. You can now change out barrels with a barrel nut and not have to modify the stocks barrel channel in any way
Grayboe memory foam recoil pad that mitigates recoil like a dream
Embedded bubble level to ensure rifle is level to the ground
Fits all aftermarket Remington 700 clone actions
No glass bedding required
Arrives to you drop in ready, bolt your rifle on and go shoot
Adjustable spacer system with 1" Grayboe memory foam recoil pad providing 12.75" - 13.75" Length of Pull adjustment. (additional spacers can be purchased if longer LOP is needed).
Adjustable cheek piece with low profile adjustment screw included. (Left hand shooters will want to use the low profile screw).
Embedded bubble level
4 Flush cups installed on RH & LH sides for sling
2 MLOK rails installed on bottom of forend
Aluminum pillar bedded
Does the cheekpiece come notched for the T3X cocking indicator?
Yes it does.
Will you ever offer Savage options?
Yes eventually. Just don't have a hard set date on when that will be.
Can you put one of the old style green bubble levels in rather than the blue?
Unfortunately not, we only have the blue level now.
Will you inlet for CIP length bottom metal and mags
Yes we can do that, CIP bottom metal is the same inlet and outer dimension as a long action bottom metal. We also sell CIP length bottom metal here, https://www.grayboe.com/collections/accessories/products/grayboe-dbm-remington-700
Is it possible to get MLok panels included at the 3 and 9 o'clock positions?
Unfortunately not, due to the lightening cuts on the forend we cannot install them there.
Are there any plans to offer a Mack Bros EVO inlet?
We have yet to see one here in shop. It appears to be a Rem 700 footprint and should work in a Phoenix stock inlet for a Rem 700. However, you may need to modify the inlet in the stock slightly for the trigger hanger to have clearance and sit into the stock correctly. This mod can be done with a steel file and take about 5 mins to do.
Is there any difference in the rem 700 inlet and the defiance anti x inlet?
There is but not on a Phoenix stock. We just list all the individual actions so customers can select their specific action.
I have a bighorn origin action and i want to put a criterion varmint contour with barrel nut. Will it fit?
Yes it will drop right in.
I have a bergara b14 ridge and would like to run the Phoenix stock and convert it to a 5 round 270 aics mags. Is that a possible set up
Yes it is, you'll just need AICS magazines for the .270 win round. Do you already have a bottom metal that accepts AICS magazines?
The only bottom metal I can find in stock anywhere is Hawkins DBM. I'm doing a 300 PRC build so LA. I don't see that as an option in the build up. Is that the same size as any of the bottom metal options you specify for the Phoenix?
We have bottom metal in stock here, https://www.grayboe.com/collections/accessories/products/grayboe-dbm-remington-700. You would want the CIP length DBM for a .300 PRC build i believe. When ordering a stock, you would select "M5 style detachable box magazine".
I have a left hand browning x-bolt long range hunter with a walnut stock I would like to cut some weight on. Is there any options for this?
Unfortunately our stocks dont' fit the Xbolt at this time.
I have a friend who has a custom 338 Lapua and is trying to get the weight down as much as possible, can the Phoenix handle a 338 Lapua, if so can other stocks?
Yes all our stocks are made with our material to handle .338 lapua easily.
Can the stock withstand a 300 PRC?
Yes it can.
One last question before I order... Thanks you for your patience. My Tikka T3x has Mountain Tactical Gen2 bottom metal, Model T3OEMDBM. Which bottom metal option do I select for use with the Phoenix stock?
To my knowledge, the Mtn tactical bottom metal fits the factory plastic tikka T3 DBM footprint.
For stocks inletted for the Tikka T3, how do you deal with the recoil lug that Tikka uses?
we install a new steel lug into the stock.
I see that the PHOENIX stock is aluminum pillar bedded. Is this sufficient to used by it self or is glass bedding still preferable. or necessary?
glass bedding is not required or necessary. We recommend bolting the rifle to the stock and go shooting. If you think you can squeeze more accuracy out of it then you can decide to glass bed.
How does the "flush cup" sling mount system work?
they are for quick detach loops for a sling, like seen here https://www.amazon.com/UTG-Heavy-Button-Sling-Swivel/dp/B003TWXA2Q/ref=sr_1_6?dchild=1&keywords=QD+loop&qid=1615067085&sr=8-6.
If I purchase a Phoenix inletted for a Defiance Ruckus would it also fit a Big Horn Origin?
Yes it will as long as both the ruckus and origin are either a long or short action length.
Hi, I'm looking for a left hand phoenix stock for a tikka t1x (. 22) could you advise what inlet I should be selecting for best fit. Thank you.
Just added the T1x to the "action inlet" drop down selection!
I have an older Ruger M77 Target rifle with 26” bull barrel .308 Do you have a stock for that..?
Unfortunately our stocks don't fit Ruger M77's at this time.
Do you have any stocks that fit the Terminus Apollo Action?
The Phoenix stock will fit the Terminus action. I just added it to the "action inlet" drop down menu so it can now be selected!
Can MLOK rails be installed on the sides of the stock like on the Ridgeback?
Unfortunately not, due to the lightening cuts on the sides of the forend we cannot install a MLOK rail there.
Could I take a Bergera approach and put the barrel and action on this stock? Does it have to keep the magazine or can it go with just a hinged floor plate?
Yes you can select "Bergara Premier" for the action inlet and "factory bergara floorplate" for the bottom metal inlet selection and your Premier approach rifle will drop right in.
Are there any plans to have these stocks available to fit a Browning A Bolt action?
eventually yes but just don't have a hard set date on when that would be.
Will this stock fit a tikka t3x in .300 win mag?
it will be in the next couple weeks!
Will this stock fit a ruger m77 25-06?
Unfortunatley at this time our stocks don't fit the ruger m77.
Will this stock fit a Bighorn TL3 Long Action?
Yes it will, you can order the bighorn TL3 inlet in the "action inlet" selection when ordering.
Could sling swivel studs be added to this?
We may be able to install a rear stud on the bottom of the buttstock and then i know you can get MLOK attachement studs on Amazon for the forend. Email firstname.lastname@example.org if you'd like to place an order with studs.
How long is the flat length under the indentation on both sides to the front of the stock. Looking to install an ARCA rail on the MLOK section in full.
the bottom of the forend on a long action to the forend tip is about 10 inches.
I have an older TC Predator in 22-250. do you make a stock for it?
Unfortunately our stocks don't fit Thompson Center rifles at this time.
Will this chassis fit or come in howa or vanguard action soon?
we hope to have it fitting the howa by mid 2021.
It's the bat igniter action
We haven't seen one of these actions in shop yet but according to BAT it will drop into a Rem 700 inlet Phoenix stock so yes it will work!
Will the bat action fit in this stock
It might, what model BAT action do you have?
Will this fit a Remington 700 with a remage barrel nut? Does the action need to be bedded?
yes it will fit your barrel nut. Our stocks do not require glass bedding. We recommend once you receive the stock you just bolt the rifle on and go shoot. Then if you think you can squeeze more accuracy out of it, then you can decide to glass bed it.
Will this fit a heavy Palma countor barrel?
yes it will!
When will the tikka CTR be available?
its looking like we are a couple weeks out.
Is it possible to get this stock with a BDL-type hinged floor plate inlet, instead of a DBM?
we will have the BDL model available in a couple weeks.
Which inlet should I choose for a Bighorn RimX Action? Should I should TL3, or Rem 700?
looks like the RimX is a total drop in to a Rem 700 inlet stock so I would order it for a Rem 700. Side note, customers have told us that 2 thin washers are needed at the rear screw on the bottom metal for the magazines to feed correctly.
Will you be offering this with BDL style floorplate soon?
yes, plan to have that out hopefully in the next couple of weeks.
Will a long action H.S. Precision DBM work with this stock?
Currently it will not. However, we are a month or so away from being able to have this DBM fit the Phoenix stock. We will add it to the bottom metal selection menu when it comes available.
Any plans for Tikka T3/T3X actions?
Yes we plan on having the Phoenix ready to accept the T3 in about a month.
Will this stock clear the trigger hanger on Kelbly and Impact actions?
I'm not aware of the trigger hanger on an Impact action but yes we do modify the stock for the Kelbly Atlas one. We could do the same cut for the Impact if need be.
Will is fit a CA ridgeline carbon wrapped barrel?
yes it will!
Will it fit a proof research barrel with a sendero contour
Yes it will.
I want to use your Ridgeback on a 6CM build that has a ARC nucleus. When selecting the inlet, should I choose the Mausingfield or standard R700 inlet?
since it appears that the Nucleus is a true Rem 700 clone action, just select Rem 700 inlet.
Does the Detachable box mag bottom metal come with it?
No the DBM does not come with the stock, it is purchased separately.
What material is the stock made out of?
Its a carbon fiber & fiberglass epoxy resin composite mixture.
Any plans to offer this in multicam black?
you bet, we just have to get one dipped to put up the photo on the website. You can order one now if you want, email email@example.com.
Great stock and and well worth the price. Probably will be my go to stock for hunting rifle builds.
Vietnam Tiger Strip dip looks amazing, fits the gun super well, tight tolerances, and light! 5 stars!
This stock is well planned out, the weight and shape of the stock have a great feel. The pillar bedding works well, and the m-rail is a great addition. The GAP splash camo is not that great and the overspray required some sanding to get a good fit at the action. Also the buttpad is terrible. But I was able to find a pacmyer pad in the same shape to replace the poor quality pad that came on the stock. Accuracy is on par with the hs precision stock it replaced and better than the 700pro that didn’t maintain a tight group I tried before this stock.
Wanted to tell you that I received my stock and am blown away by the construction and quality of this thing , can't wait to slap the components together and give it a test ! thanks again for a great product !
Reduced the weight of my hunting rifle by 2 pounds and still provides the adjustable options I must have because of my long arms and scope height.